Epicep 21H Technology Site

Posts Tagged ‘intro’

When you’re preparing to pass the CCNA exam and earn this coveted Cisco certification, you’ve got to be totally prepared for the many kinds of binary and subnetting questions Cisco may throw at you. You also have to be familiar with the different manners in which a subnet mask can be expressed, as in the following:

255.255.255.0
Read the rest of this entry »

In studying for your CCNA exam and preparing to earn this valuable certification, you may be tempted to spend little time studying static routing and head right for the more exciting dynamic routing protocols like RIP, EIGRP, and OSPF. This is an understandable mistake, but still a mistake. Static routing is not complicated, but it’s an important topic on the CCNA exam and a valuable skill for real-world networking.

To create static routes on a Cisco router, you use the ip route command followed by the destination network, network mask, and either the next-hop IP address or the local exit interface. It’s vital to keep that last part in mind – you’re either configuring the IP address of the downstream router, or the interface on the local router that will serve as the exit interface.

Let’s say your local router has a serial0 interface with an IP address of 200.1.1.1/30, and the downstream router that will be the next hop will receive packets on its serial1 interface with an IP address of 200.1.1.2/30. The static route will be for packets destined for the 172.10.1.0 network. Either of the following ip route statements would be correct.

R1(config)#ip route 172.10.1.0 255.255.255.0 200.1.1.2 (next-hop IP address)

OR

R1(config)#ip route 172.10.1.0 255.255.255.0 serial0 ( local exit interface)

You can also write a static route that matches only one destination. This is a host route, and has 255.255.255.255 for a mask. If the above static routes should only be used to send packets to 172.10.1.1., the following commands would do the job.
Read the rest of this entry »

ISDN is a vital topic for today’s CCNA and CCNP candidates, especially for the ICND and Intro exams – you’ve got to know ISDN inside and out to pass those exams. Naturally you want to include it in your home lab. What many candidates don’t realize is that you can’t connect two Cisco routers directly via their Basic Rate Interface (BRI) interfaces you’ve got to have another device between them called an ISDN simulator.

An ISDN simulator is not one of those software programs pretending to be routers (“router simulators”) this is a piece of hardware that acts as the telephone company in your home lab. Older simulators come with preprogrammed phone numbers and SPIDs, where newer ones let you program the phone numbers you want to use. Either way, an ISDN simulator is great for your CCNA/CCNP home lab, because you can practice dial scenarios that actually work. And you get to troubleshoot the ones that don’t, which is also important to learn! )
Read the rest of this entry »

Whether you’re on the road to the CCNA, CCNP, MCSE, or you’re on any other computer certification track, the odds are that sooner or later, you’re going to fail an exam.  It’s happened to almost all of us, yours truly included.   What you have to keep in mind in these times is that success is not a straight line.  You’ve probably seen charts showing the growth of an industry or a business — you know, the ones that go from left to right, and look kind of jagged.  The line goes up for a while, then down a bit, then up some more, then down a little.

The key?  While every business has its setbacks, the net result is that the line goes up and progress is made.  That’s how you want your certification pursuit and your career to go as well – upward!

I’m not asking you to be happy about failing an exam.  You’re allowed to get mad for a few minutes, vow to never take another exam again, and be disappointed.  What you’re not allowed to do is stay that way.
Read the rest of this entry »